Home > Error Code > Rheem Error Code 33 Furnace

Rheem Error Code 33 Furnace

Contents

that is a MOD furnace (modulating). Reply On November 24, 2015 at 9:44 pm Don said: I'm code 33 and then 13 I've replaced the fan limit . could it be a gas line pressure? Reply On October 27, 2011 at 7:23 pm Kevin Jaeger said: Hey hope someone can help…….Have a 33 code that changes to 13. this content

Will only blow cold air. Please keep in mind that the roll-out tripped for a reason. The Home Smithy is online now I have a Rheem RGRA06EMAES condensing gas furnace. Support the Skilled Trades, Don't DIY Reply With Quote 02-20-2013,09:29 PM #6 TriWorksInc View Profile View Forum Posts View Forum Threads Regular Guest Join Date Feb 2010 Location Northeast, PA Posts

Rheem Furnace Fault Codes

I personally have never put much stock in the superscrubber filters myself. The schematic stuck to the door is the same #, but rev. 04. I figure that if you clean the things your body uses too much it wont be able to fight the nasties when they do attack. Ask Comfort Specialist Your Own Question Comfort Specialist, HVAC Technician Category: HVAC Satisfied Customers: 1368 Experience: Master Lic.

I'd be glad to help. For now, he just reset it. Anyway, you saved me a lot of money! Ruud Furnace Error Codes Please advise how you wish to continue.

My old furnace had a heat exchanger that had to be inspected every year for dangerous cracks. Rheem Furnace Control Board Codes grayfurnaceman 500,498 views 7:10 Rheem RGPH: Testing Ignitor & Flame Sensor | With Fritzhvac - Duration: 9:56. I am a hvac tech and have found several of these furnace go bad in less than 10 yrs.

We woke up on a Sunday morning with the house temp at 55 degrees and dropping.

I could not find an open anywhere. Rheem Furnace Error Code 45 Transcript The interactive transcript could not be loaded. Loading... It is located in 10/30/2016 10/30/2016 centralappliance1 Furnace blower stopped.

Rheem Furnace Control Board Codes

I am not a contractor, can I still sign up? The switch wire was crowded against the tin box housing the line-in connection and had rubbed off the insulation, from furnace operating vibration over the last ten years. Rheem Furnace Fault Codes Those are manual reset. Rheem Classic 90 Plus Troubleshooting Codes It will do that if the board sees any open limits, hi-limit, aux limit, flame roll out, blocked vent switch (spill switch).The "Okay" light flashing usually is related to "twinning" problems.

You really need to get a RHEEM guy out there... news sooner or later you will find something of interest. Click on browse. I removed the 16 x 25 inch cold air return filter and it now works fine. Rheem Furnace Error Code 57

We've sold these for 10 years, my Sister got one of the test furnaces. Reply On May 29, 2014 at 5:15 am best property companies to work for said: Your mode of telling the whole thing in this piece of writing is actually fastidious, all If you are in school and doing a project... have a peek at these guys Rating is available when the video has been rented.

Furnace wasnt working, couldnt figure out what was wrong for the life of me High limit was stuck, tapping it fixed the issue, so simple Reply On February 14, 2014 at Rheem Error Codes Especially the switch re-set Reply On February 19, 2012 at 10:54 am Dianne Ranson Salt said: I have an error code 34 also, clicked on the thumbnail and can see what Glenn Harrison, Residential Service TechicianAlthoff Industries, Crystal Lake, IllinoisAlthoff Industies Link 0 · John Mills Member Posts: 221 April 2003 Rheem fault codesGeneral TopicsStandard Furnace Diagnostic Codes(GT0003) Does not include Modulating,

It will be behind the cover on the upper half of the unit on the fire box. Ask Your Own Appliance Question Customer: replied8 years ago.

Any Ideas??? chris eigenheer 1,813 views 0:45 Ruud Furnace Error Codes - Duration: 2:47. Let me check see if I can find the physical switch. Twinning Circuit Fault Contest! ! ! ! !

However, six flashes means the line and neutral are reversed.I can only imagine that coming up if the thing was miswired when first installed.Rheem furnaces have a CFM LED too.Those are Reply On June 25, 2011 at 9:45 am david scherer said: Excuse me my uninformed friend , the flame roll out switch is opening due to a heat exchanger blockage or then power back on. http://newsocialweb.org/error-code/res-error-code-1.html It just started 5/28/2016 5/28/2016 smitty1486 I have a built-in Sub-Zero refrigerator, 7 years old.

Reply With Quote 02-20-2013,10:35 PM #10 qwerty hvac View Profile View Forum Posts View Forum Threads Professional Member* Join Date Dec 2008 Location Buffalo NY Posts 3,180 Post Likes Likes (Given) Powering off the furnace and restarting would trigger the gas ignition, but it would not stay on. This indicates the system is off on high limit or a bad connection in the limit circuit. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next.

folks can cause a lot of damage and potentially create an unsafe condition if they try. What does 7/24/2016 7/24/2016 centralappliance1 We bought a GE Water Softener 40,000 gr GXSH40V at Home 7/21/2016 7/21/2016 smitty1486, johnnn40, JACUSTOMER-am4mdajw- When I wash clothes I get water on the side As a registered Guest you will be able to: Participate in over 40 different forums and search/browse from nearly 3 million posts. Control Board #62-25338-01 - Duration: 2:31.

Visit https://heatinghelp.com/contact-us/. See my post above to "June 25, 2011 at 9:45 am david scherer" It sounds like I'm having the same problem as you. Square on, please about 1 1/2' away would be about right. Ask Your Own Appliance Question Customer: replied8 years ago. My husband followed your instructions and reset our furnace.🙂 Reply On February 24, 2013 at 3:11 pm Paul said: Thanks David, you gave me the confidence to look at sensors and,

I that repair cost $325 parts. & labor for a 15 minute job. have checked most switches but could use some data on this, none available. Reply With Quote 02-20-2013,10:17 PM #9 TriWorksInc View Profile View Forum Posts View Forum Threads Regular Guest Join Date Feb 2010 Location Northeast, PA Posts 233 Post Likes Likes (Given) 0 I figured it was a bad logic board so I changed out the board however still have the same error code. ' Does anyone have any ideas Reply With Quote 02-20-2013,09:16

Reply With Quote Page 1 of 2 12 Last Jump to page: Quick Navigation Tech to Tech Chat - Residential Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Use the blue cheap woven filters.