Remote Access Error Message
ERROR_STATE_MACHINES_NOT_STARTED 695 State machines are not started. JSI Tip 8960. ERROR_OAKLEY_TIMED_OUT 792 The L2TP connection attempt failed because security negotiation timed out. Advertisement Related ArticlesJSI Tip 0558 - Remote Access Service (RAS) error codes. Check This Out
Note Supported in Windows Vista and later versions of Windows. ERROR_VPN_REFUSED 808 The network connection between your computer and the VPN server could not be established because the remote server refused the Edit connection properties and select different protocol for negotiation and try again. ERROR_BAD_STRING 637 A string was detected that could not be converted. If the authenticating server is an IAS server, the following registry settings in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan\PPP\EAP\13 can modify the behavior of the EAP-TLS when performing certificate revocation.
Make sure that the parameters of the connection have appropriate permissions through remote access policies. ERROR_SMART_CARD_REQUIRED 779 To dial out using this connection you must use a smart card. You just need to reboot or off/on your router to clear any current upnp entries.
In this situation, if the remote access client is only configured to use TCP/IP as a LAN protocol, the connection attempt is denied. The VPN client must have a valid computer certificate installed that was issued by a CA that follows a valid certificate chain from the issuing CA up to a root CA JSI Tip 0558 - Remote Access Service (RAS) error codes. Check the event log.
Issued certificates can be revoked at any time. ERROR_NO_ISDN_CHANNELS_AVAILABLE 714 No ISDN channels are available to make the call. Click OK to exit Telephony Properties dialog box. http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/error-711-cannot-load-the-remote-access-connection/61ef37bd-b21b-4aad-a38c-0a3c9048af5a Last but not the least, don't forget to turn on your WiFi radio before you attempt to tether!
I have checked the settings from the myCloud at home, and I can connect to the drive with myCLoud Desktop, and myCloud is visible in my network. THE FIX: 1) Enable all services as advised in the "Let me fix it myself" section of this page. ERROR_PORT_NOT_OPEN 618 The specified port is not open. Note Supported in Windows XP and later versions of Windows. ERROR_REMOTEACCESS_NOT_CONFIGURED 956 Routing and Remote access server is either not configured or not running.
Finally, to trust the certificate chain offered by the authenticating server, the remote access client must have the root CA certificate of the issuing CA of the authenticating server certificate installed Get More Info ERROR_ACCESSING_TCPCFGDLL 727 Cannot access TCPCFG.DLL. Note Deprecated in Windows Vista and later versions of Windows. ERROR_FROM_DEVICE 651 Your modem or other connection device has reported an error. Note Supported in Windows Vista and later versions of Windows. ERROR_PEAP_CRYPTOBINDING_NOTRECEIVED 824 Crypto-Binding TLV was not received.
Note Supported in Windows Vista and later versions of Windows. ERROR_IPSEC_SERVICE_STOPPED 827 The L2TP/IPsec connection cannot be completed because the IKE and AuthIP IPSec Keying Modules service and/or the Base Filtering Engine his comment is here Some network services or resources might not be available. We appreciate your feedback. Possible error messages The following common Windows 2000 remote access client errors occur when users are not able to connect to the remote access server.
ERROR_OAKLEY_ERROR 793 The L2TP connection attempt failed because an error occurred while negotiating security. ERROR_LINE_BUSY 676 The line is busy. The certificate has not have been revoked. this contact form Click Apply to save your changes.
Fix Windows 10 activation problems Fix USB drive issues in Windows 8 Resolve Camera Not Working Issue in Windows 10 How to fix Ethernet controller driver issue in Windows 7? The remote access client does not use these settings. If broadcast cannot be enabled, try to make the remote access server the master browser.
NoRootRevocationCheck When set to 1, IAS prevents EAP-TLS from performing a revocation check of the remote access client's root CA certificate.
Click OK to exit Remote Access Auto Connection Manager Properties dialog box. ERROR_ACCT_DISABLED 647 The specified account is disabled. Windows XP displays error 1068 when you start the Remote Access Connection Manager service or the Remote Access Auto Connection Manager service? ERROR_PORT_OR_DEVICE 692 A hardware failure has occurred in the port or attached device ERROR_NOT_BINARY_MACRO 693 The macro is not a binary macro.
Error 766 Connections that use the L2TP protocol over IPSec require the installation of a machine certificate, also known as a computer certificate. Note Supported in Windows Vista and later versions of Windows. ERROR_EAPTLS_CACHE_CREDENTIALS_INVALID 826 EAPTLS validation of the cached credentials failed. One of the best tools for troubleshooting IPSec authentication issues is the Oakley log. http://newsocialweb.org/remote-access/remote-access-connection-manager-error-5-access-denied-xp-sp3.html Make sure you are connected to the Internet and use the checklist provided earlier in this section to ensure that you are connecting to the correct server name or IP address
Additionally, you may fail to install any network adapters on your computer. The content you requested has been removed. ERROR_CERT_FOR_ENCRYPTION_NOT_FOUND 781 The encryption attempt failed because no valid certificate was found. Dev centers Windows Office Visual Studio Microsoft Azure More...
You can use the netsh ras show registeredserver command at the Windows 2000 command prompt to view the current registration. Note Supported in Windows Vista and later versions of Windows. ERROR_IDLE_TIMEOUT 828 The connection was terminated because of idle timeout. Otherwise, the routing protocol of your routed infrastructure on the remote access server must be enabled. Wait a few seconds and redial. 713 No active ISDN lines are available. 714 Not enough ISDN channels are available to make the call. 715 Too many errors occurred because of
If you have implemented full domain browsing by using only entries in LMHOSTS files on all computers, you are limiting browsing to the local domain. For the authenticating server to validate the certificate of the remote access client, the following must be true for each certificate in the certificate chain sent by the remote access client: That was the cause for all my grief. Note: If you add or remove the remote access server computer to the RAS and IAS Servers security group, the change does not take effect immediately because of how Windows 2000
ERROR_ALREADY_DISCONNECTING 617 The specified port or device is already disconnecting. ERROR_NO_EAPTLS_CERTIFICATE 798 A certificate could not be found that can be used with the Extensible Authentication Protocol (EAP). Note Supported in Windows Vista and later versions of Windows. ERROR_NOT_NAP_CAPABLE 836 The machine is not NAP capable. For IP-based remote access clients, IP routing should be enabled.
Note Supported in Windows 7 and later versions of Windows. ERROR_INVALID_PREFERENCES 846 Either VPN destination preference is not selected by the user or it is no longer valid. Note Deprecated in Windows Vista and later versions of Windows. WARNING_MSG_ALIAS_NOT_ADDED 644 You will not receive network message popups. Note Supported in Windows Vista and later versions of Windows. ERROR_VPN_BAD_CERT 810 A network connection between your computer and the VPN server was started, but the VPN connection was not completed. Note Supported in Windows Vista and later versions of Windows. ERROR_USER_LOGOFF 830 The connection was terminated because user logged off.
ERROR_READING_USAGE 673 Cannot read the usage from the media .INI file. ERROR_CANNOT_PROJECT_CLIENT 634 Your computer could not be registered on the remote network. then go into device manager and check the net stuff in devices. –Psycogeek Mar 5 '12 at 19:23 add a comment| 5 Answers 5 active oldest votes up vote 3 down